log splitter valve sticking

Quick wild guess. The hydraulic directional valve controls the motion of the cylinder.

Log Splitter Valve 20 Gpm 1 2 Work Ports Auto Return Detent

Another reason for a slowed-down log splitter is a jammed motor due to blockage in the fan.

. Works great but the actuation lever sticks in the up position so tightly. When it retracts it pulls in tight and stalls the engine. I pulled the cap and.

Valves can often be unstuck by rotating the cam huge lifting force available and then driving them back down a few times. Its a Huskee 22 ton and the valve is sticking both ways. Dec 12 2005.

In the second stage or low flowhigh-pressure stage the pump. When you forced the spool back to center you finished destroying. The spool shifted by the handle has 3 positions.

Valve core requires cleaning. At first I thought that I had lost some hydraulic. My new to me Countyline Speeco 25 ton splitter control valve detent mechanism was sticking operating erratically and adjusting didnt solve the problem.

I have a Power Pro log splitter made by Brave Model HP-1226F. The Hydraulic Log Splitter Valve. You need to check the amount of oil first.

Log Splitter Valve And Accessories By Energy Manufacturing Company Inc If a log is not splitting all the way through then the log may be too green or too large meaning that it. You can check for this issue easily. Fixing the auto-return on a hydraulic control valve usually is just a matter of tightening The bolt inside the detent cover assembly.

If reallydamnstuck centerpunch the suckers and drill down through the middle of the valve head increasing drill size until head is detached. The seals on these pumps wear over time and eventually can cause hydraulic fluid to leak out of the system. This tutorial apply to the Energy control.

I have a manual 10 ton hydraulic log splitter purchased from Northern Tool and I also have a problem with a loss of driving force. If fluid is leaking from your pump disassemble it and replace all seals. First turn the log splitter over and close off the air vent remove the motor and pump 3 x 13mm headed bolts and 1 x support bolt.

If youre used to the lever going one way on one log splitter you might have overlooked the valve position on a different log splitter that works differently. Common problems with AL-KO and similar Chinese generic log splitters the hydraulic valve spindle breaks on the end stopping the unit from working correctly. Now drivedown the surviving junk pull guide retainers and carry on.

Remove the fan cover and try to turn it to see if it moves without. I have a Brave Log splitter and the last few weeks the detentspoil valve has become sticky after the I split a couple of hours. Pushed one way it shunts oil.

This will remove all the excess air trapped inside the splitter. I took the valve. The hydraulic valve has.

Also it is hard to trip the lever to get it to stop retracting. Place the log splitter back upright and try. It happens due to either the lower level of fluid or the air present in the system.

If youre used to the lever going one way on one log splitter you might have overlooked the valve position on a different log splitter that works differently. Up to 32 cash back The log splitters hydraulic control valve directs the hydraulic fluid flow to the hydraulic cylinder to extend and retract the piston and wedge. When attempting to split logs check that the end of the valve stem remains in contact with the face of the lever when the lever is depressed and released.

On one side of the valve there is a inch long bolt only way I know how to describe it with a ball in the end. A detent valve lever can be pushed up or down to put the valve into operation. If the oil is found to be enough then the problem is due to the air mixed.

If still your log. If the log splitter seems weak or not performing as it should then there is a strong likelihood that something is not right with how the splitter system is operating. Stuck Troubled Vintage Ads Community Album Photo Ad Archives.

Check the manual to be sure you have proper lever position. Check the position of the lever. Other than that it works fine.

To begin with check your log. Anyone ever rebuild a log splitter hydaulic valve. Now release the ram and put back the oil-filling plug.

If your log-splitter is moving slow but still capable of splitting the wood it always has it is most likely stuck in its second stage. And now it started to stick going out and it will go out to the end and stall the engine. Its working but not correctly.

Just rotate clockwise the oil-filling plug and remove the plug. I just bought a sweet 22-ton Splitter at Tractor Supply the Husky model made by Speeco I believe. The o-ring sealing the spool to the valve body got damaged and caused the spool to stick.

Log Splitter Valve And Accessories By Energy Manufacturing Company Inc

Log Splitter Valve 20 Gpm 1 2 Work Ports Auto Return Detent

Troy Bilt Mtd 27 Ton Splitter Valve Repair Youtube

Performance Built 27 Ton 208 Cu Cm Horizontal And Vertical Gas Log Splitter With Briggs Stratton Engine In The Hydraulic Gas Log Splitters Department At Lowes Com